Cleaning the Nozzle and Venturi
- To get to the nozzle and venturi remove the top cover. Be sure the unit is in its normal operating cycle/soft water cycle (no water pressure at nozzle and venturi).
- Wash the parts in warm, soapy water and rinse in fresh water.
- Carefully replace all parts in the correct order.
How do I clean my GE water softener?
Clean your GE water softener at least twice a year or more often if necessary.
- Lift the lid on top of the water softener and locate the brine well.
- Mix 1 cup of resin bed cleaner and 1/2 gallon of cold water in the bucket.
- Pour the cleaner into the brine well.
- Taste or smell some cold tap water.
What is the venturi valve on a water softener?
brine water
The venturi valve in your water softener draws brine water from the salt tank to the resin tank for regeneration. Follow these steps to replace a damaged venturi.
How do you clean a resin bed in a water softener?
There are two ways to clean the tank: The first is to unplug the water softener unit and remove the resin tank by unscrewing the bolts and disconnecting the valve. You can then clean the tank using bleach and water before reinstalling the tank.
How much water should be at the bottom of a GE water softener?
We recommend keeping your brine tank at least one quarter full of water softener salt at all times, and no more than four to six inches below the top of the tank for optimum efficiency. Make sure that the salt level always remains a few inches above the water level.
What does the float do in a water softener?
Most water softener systems should come with a device called a safety float. This tool’s job is to shut the water that flows into the brine tank off if it gets too much water supply. It is known as a safety float because it ensures that the water softener tank doesn’t overflow or lead to a flood.
What is water softener resin cleaner made of?
Water softener resin is an inorganic plastic made of polystyrene and divinylbenzene, or DVB.
How do you clean sediment out of a water softener?
Pour a few tablespoons of dish soap into 1-2 gallons of water to create a soapy mixture. Pour the soap/water mixture into the brine tank and scrub the inside with a long-handled brush. Dump and rinse with water. Now pour 2-3 gallons of clean water into the brine tank with a quarter cup household bleach.
Where is venturi located water softener?
Locate the Venturi hanging off the left-hand side of softener head. The venturi is a gray plastic base with a white cone cap (pictured below). 4. Unscrew the cone cap and take out all seven (7) internal pieces, so you are left with just the empty gray housing.
How do you clean a brine valve?
Remove the salt plate at the bottom of the brine tank. Lay the salt tank on its side and direct a brisk stream of water from your garden hose to its inside to rinse out all residue. Using a household scrub brush and a mild soapy solution, clean the salt plate. This will complete the tank cleaning.
Does vinegar clean water softener resin?
Can I put vinegar in my water softener? Yes; follow the same instructions for cleaning the tank with bleach. You can also mix the vinegar with water if you’d rather just scrub the brine tank instead of running a full cycle.
What does the venturi valve do in a water softener?
The venturi valve in your water softener draws brine water from the salt tank to the resin tank for regeneration. Follow these steps to replace a damaged venturi.
How do I contact GE about a water softener?
Installation for Water Softeners and Water Filtration Systems To find an authorized installer in your area, call 1-800-952-5039. GE water softeners save on salt, water, and energy by using up to 50% less detergent for laundry and dishwashing*, using up to 34% less salt and up to 35% less water during regeneration.**.
How do I clean the inside of my water softener?
Remove the softener top cover. Unscrew the cap from the nozzle and venturi housing, being careful with the large O-ring seal. Lift out the screen support and screen, then the nozzle and venturi. Wash the parts in clean warm water, using a small brush or toothpick to remove debris. Clean the gasket, small screen, and flow plugs as well.
How do I adjust the hardness on my ge water softener?
Solution: Press the MODE/SET button on your GE water softener until the arrow points to HARDNESS. The number shown should match your actual grains per gallon of hardness in your water.
